109 press releases : Hydraulics: Cylinders, Pumps, Solenoid Valves…

Hydraulics specialist Holmatro puts heavy duty lifting applications in a new perspective by introducing its aluminium cylinder line. Compared to steel models, the new lightweight cylinders are easy to handle. Mastering power All Holmatro products are based on the ground rule that forces can only be applied usefully when controlled effectively. The new aluminium high pressure hydraulic cylinder...

HAVANT, UK… Diversified industrial manufacturer Eaton Corporation has added a new Series 760 variable displacement closed circuit piston-type pump and fixed motor to its heavy-duty product offering. Intended primarily for mobile vehicle applications, the new pumps and motors are available with displacements of 130cc/rev at 3200 rpm operating speed, and 160cc/rev at 2950 rpm operating speed. Working...

HAVANT, UK … Diversified industrial manufacturer Eaton Corporation today announced that its proprietary Eatonite™ Laser Clad coating technology was certified by independent test services company DNV after fulfilling requirements stated in the “Guideline for qualification of wear and corrosion protection surface materials for piston rods” developed as part of a Joint Industry Project (JIP). “Eato...

These swing clamps are particularly suitable in all cases where the insertion and removal of the piece during machining must be facilitated. The clamping cycle takes place in two phases: one of clockwise or anti-clockwise rotation with partial descent of the piston, and one of a vertical downward stroke for the clamping effect. In single-acting models when the pressure is released, the clamping...

Bard Engineering GmbH has developed a unique concept for the foundations of wind turbines. The mast is placed on a supporting cross piece that rests above the water surface on three main pilings. Enerpac's Synchronous Lifting System is used to level the supporting cross piece accurately and quickly. Bard develops, manufactures or assembles all parts in their own factory, including the ‘Wind ...

Stageco – U2 stage The stage for U2’s 360o Tour is being constructed using Enerpac’s Synchronous Lift System Trendsetting hydraulics application for U2 stage The Belgian company Stageco has constructed three gigantic, identical stages for the current U2 360° Tour. The 30m high stage construction consists of a central “block” which rests upon four legs made up of six sections. What mak...

Casappa offers a wide range of gear or piston pumps and motors and filters. Many functions, such as valves and controls, are directly incorporated in the products in order to optimize space and costs for the system. With our products you can choose standard configurations and multiple combinations or assign us with the personalized development of a specific application. Gear pumps and motors m...

BROADVIEW, IL, Simplex has introduced its new G1 Series power pump platform. Starting at 30 lbs., the new G1 power pumps are extremely lightweight and easy to transport. These portable electric hydraulic pumps offer pressures up to 10,000 psi (700 bar), and are ideal for a broad range of industrial / MRO and construction applications. G1 Series models are available in standard and bolting pump ...

-G4 Standard Electric is Powered by a 115V - 60HZ, 1-1/2 hp induction motor (1,725 rpm); low startup voltage, draws 16 amps at full load (230V models available). -G4 Gas pump is powered by a 4 hp Briggs & Stratton gas motor. -Electric models are equipped with a 15’ remote power controlled pendant. -Reservoirs available in 1.5-20 gallons; welded steel designs. -Ideal for use with mid siz...

The Quincy QSV direct-drive rotary screw vacuum is designed for easy installation and maintenance. The direct-drive package is designed to easily fit through a standard doorway, and all maintenance items are conveniently accessed from one side. The Quincy QSV offers quicker cycle times and more powerful hold-down when you need it.

The Elettrostart solenoids offer high performances both of force and of stroke (up to 50 mm) in relation to the sizes fairly reduced. The pull coil by the high power (intermittent duty) is able to guarantee a force greater than the traditional single coil electromagnets. The Elettrostart solenoids usually are used for the stop and the acceleration of diesel engines. There are two versions: ...

Bimba Manufacturing today announced the introduction of its new non-contact pneumatic position feedback cylinders, for applications that previous technology could not address. Unlike traditional pneumatic feedback technology, the PFCN models are resistant to the effects of moisture, oil, airborne debris, dust and airline contamination. In addition, each cylinder is factory calibrated for precise...

Our company is specializing in manufacturing NdFeB magnets, we produce according to custom-design. Our magnets are widely used in industry , Motor Magnets, Rotor magnets, Pick-up Magnets, Fixing and Pull Magnets, Holding and Catch Magnets, Automotive Magnets, Car magnets, Lifting Magnets, Wind turbine magnets, Power magnets, Speaker Magnets, Filter Magnets, Pot Magnets, Office Magnets, Bio-Mag...

A GOOD NEW FOR THE HYDRAULIC! SERV-CLIP® THE PIPE MEASURING POINT is a patented product and registered trade mark of BKM in Hagen-GERMANY. - Connect into system UNDER PRESSURE up to 630 bar (9100 psi) WITHOUT TUBING SEPARATION IN 3 MINUTES - (incl. M16X2) ALLOWS CONNECTION OF SENSORS AND SCREWED COUPLINGS CHECK IMMEDIATELY: Pressure, Temperature, Flow Rate, Lea...

The HP pump is operated through a foot pedal and it's small, handy and portable. It is compact and have an oil capacity of 1,4 litres (this is the only tank capacity available fo this type of pump), enough to fill up long cylinders. The HP is meant for high working pressures: 250 - 500 up to 700bar depending on the choice of the size of the piston, to obtain respectively 2,2 - 1,4 e 0,8 L/m...

SAI S.p.A. is a leader company in the Marine & Offshore Market, most of its production of hydraulic radial piston motors is devoted to marine applications, such as: net winches, anchor winches, hold cover winches, crane winches, upper deck winches, capstan drives, thruster steering drives, rudder steering drives, propeller drives, fishing pumps, fishing presses, offshore drilling equipment, flow di...

The breakthrough in hydraulic pump technology & ergonomics 10.000 psi (700 bar) pumps with XVARI® Technology, exclusively from Enerpac! Ergonomic design for reduced operator fatigue. Variable oil flow & fine metering for precise control. Higher oil flow for increased productivity 15 in3/min at 10.000 psi (0,25 l/min at 700 bar).

Product Announcement September 15, 2009 PG30 PUMP with 4-stroke engine • New Honda 4-Stroke Engine (Compliant to the European standards, CE approval) • Meets future EPA emission requirements Weight: 16kg (with 3.79l of oil) PG303 • Single-acting applications • 9520 valve • Separate return line allows oil to return to reservoir PG304 • Double-acting applications • 9506 4-way (ta...

Technology in delayed coking units has changed drastically. In combination with the development of automatic top and bottom valves, automatic drilling/cutting tools and hoist drivers have high performance cutting systems realized large improvements in safety and reliability. Dr. Wolfgang Paul from Ruhrpumpen has many years of experience in the Decoking business and managed to bring the products of ...

“Our customers are telling us our presses are the best they have ever operated. They like the fact that the load-sensing hydraulic system makes the press more energy conscious, more consistent in operation, and quieter. And we all like the fact that our new hydraulic system is 15 percent lower in price than our previous system.” Tim Altomare, Fabriweld Controls Engineer Background Sometimes a...